USED 1/2 OFF(800)727-1954
Power Mac Lift Gate

Mac / MacsLift / Macs / Vertical Platform Lift / Porch Wheelchair Mobility
Elevator

Download the PL-50 Mac / MacsLift / Macs / Vertical
Platform Lift / Porch Wheelchair Mobility Elevator
Document
MAC's Vertical Home Lift Specifications
The MAC's Vertical Home Lift was designed
and engineered for home use. It's easy to operate
easy to install and virtually maintenance free.
Every safety detail has been carefully designed into
the PL-50 and PL-72, including a non-slip platform,
constant pressure switches, a low platform for easy
roll-on/roll-off, safety barrier and railing, and
rolled edges.
The PL-50 and PL-72
are sturdy enough to lift and lower up to 600 pounds
and will accommodate electric wheelchairs and
scooters. Running on a gear box and chain, the PL-50
and PL-72 provide a smooth and quiet up and down
ride, requiring little maintenance. All mechanics
are fully enclosed, yet easy to access through the
rear or front of the housing unit. The lifts are
completely weatherized and attractively finished in
off-white. Shipped fully assembled, the PL-50 and
PL-72 install in 6 easy steps. The Mac's Vertical
Home Lifts are the economical and practical answer
to stair barriers.
Quality Assurance
Manufacturing
A company with not less the thirty eight (38) years
of experience in the design, fabrication and
installation of specialized lifting equipment for
handicapped and geriatric consumers should supply
the lift.
Performance Requirements
The unit shall be assembled and prewired (less
optional equipment and necessary gates) and
manufactured with adequate lifting and load capacity
for application described elsewhere in this
specification.
The unit shall be easy to operate by the user or
attendant and shall be capable of functioning in all
weather conditions.
The unit shall have the capacity
to lift up to 500 lbs. to the desired lifting height
up to a maximum lift height of six ( 6 ) feet.
Composition of Materials
Machine tower: 14 gauge cold rolled steel.
Base frame: 1 1/2" square x 3/16" Structural steel
tubing.
Lift weldment: 1 1/2" x 3" x .188" wall structure
steel tubing.
Tower cap: 10 gauge cold rolled steel plate
Side Guard Rails: 1" round x .120" gauge steel
tubing (frame).
Platform: 14 gauge cold rolled steel plate with slip
resistance surface.
Access ramp: 11 gauge steel plate with slip
resistance surface.
Electrical box: 16 gauge galvanized steel
Switch box: Hi-impact A.B.S. Thermoplastic
instrument case.
Limitations: Vertical platform lift shall operate
both indoors and out, and must be anchored on a
level, 4" thick, 3500 psi reinforced concrete
surface or pad.
Electrical System &
Wiring:
The unit shall be pre-wired by manufacturer with
exterior grade thermoplastic coated wiring.
Extension Cord, 14 gauge UL-CSA approved is
recommended if power source is not within three (3)
feet of Machine tower. Machine may also be wired
using water proof conduct.
Powder Coat Finish Prep,
Primer, & Powder Coat Process
1. 3 Stage wash, soapy water, clear water, and Iron
Phosphate which is applied to parts.
2. Parts are inspected and scuffed
3. Epoxy Primer is applied
4. Parts are baked at 250 degrees for 15 minutes
5. Parts are inspected and scuffed if needed
6. Huebert O'Brian Powder-TCIC Polyester
7. Mixed with Paint, Color Almond PFT-500-SS
8. Powder Coat is applied and baked at 400 degrees
for 30 min.
9. Parts are inspected and scuffed if needed
Safety Devices
The unit shall have the following safety features
for protection of users and the general public:
ï Upper and lower limit switches
ï Instant Reverse Motor
ï Powered with 110 volt AC current, by 1/2 HP motor,
6.4 Amp
ï Grounded electrical system
ï Heavy duty worm drive gear box with heavy duty #50
lifting chain
ï Automatic access ramp
ï 36" guard rails on non-enter and exit sides of
platform
ï Non-Skid platform and access ramp surface
ï Key-lock control
ï Switching & Control system 24 VAC low voltage
currentInstallation
The contractor
shall do all work and supply all materials necessary
for the complete installation, It is the intent of
this specification to outline broadly the equipment
required but not to cover the details of design and
construction.
Maintenance
Maintenance of the vertical platform lift unit shall
consist of regular cleaning of the unit, protection
of the painted surface of the unit.
Warranty
Unit shall have one ( 1 ) year limited warranty on
the basic unit and electrical system with a two (2)
year warranty of drive train components.
Note
This specification has been written to assist you
and your consumer in preparing an accurate and
detailed description for specifying a vertical
platform lift. All or part of this specification may
be reproduced. Additional technical information is
available from our Mac / MacsLift / Macs / Vertical
Platform Lift / Porch Wheelchair Mobility Elevator
Engineering Department.
Mac / MacsLift / Macs / Vertical
Platform Lift / Porch Wheelchair Mobility Elevator
PL-52 PL-72Macslift Mobility Bruno
VPLHarmar
Cheap Discount Best Quality Sale
Disabled Harmar Wheel Chair
Trus-T-Lift Trustylift 4 ti 12
feet Residential and Commercial Elevator Vertical Platform Lifts



USED 1/2 OFF(800)727-1954

Mac / MacsLift / Macs / Vertical Platform Lift / Porch Wheelchair Mobility Elevator
|
Mac / MacsLift / Macs / Vertical Platform Lift / Porch Wheelchair Mobility Elevator
PL-52 PL-72Macslift Mobility Bruno VPLHarmar
Cheap Discount Best Quality Sale Disabled Harmar Wheel Chair
Trus-T-Lift Trustylift 4 ti 12 feet Residential and Commercial Elevator Vertical Platform Lifts
|
|
![]() |
|
![]() |
![]() |
|
![]() |
![]() |